Poynor Roofing Tearing Off Roofs
Poynor Roofing has been in the Arizona Area repairing roof for a while now. The Phoenix Area has been pumbled by a massive storm that swept through the state of Arizona a few months ago. There are many homes that have been damaged be the gigantic hail storm that slammed the area last October. There is still a lot of work going on even months after the storm first struck.
There are a lot of areas that were affected by the storm in the Phoenix area. The surrounding cities also were hit by wind and hail leaving many homes with leaks and damaged shingles. There are many styles of roofs in the Phoenix area that were damaged. One of the areas affected by the hail storm was around Scottsdale.
Scottsdale is known to have a lot of foam roofing. Foam roofing is something that could have been damaged by the recent hail storm. Another type of roofing very prevalent in the Phoenix area is the Tile roofing. Tile is very durable and not very often is it damaged by smaller hail. There was some hail in the Phoenix area that was big enough to damage some of the tile roofs.
Poynor Roofing
Poynor Roofing specializes in replacement of shingled roofs. The shingle roofs are the ones that are most prone to damage from hail. All roofs can be damaged by Hail if it is large enough. Another type of roofing that can and was damaged by the recent hail storm in Arizona was the Wooden Shingles. Cedar Shake shingles can break and split with enough hail.
Poynor Roofing can replace or repair virtually any type of roof, but one of the most important steps that Poynor Roofing makes is that it strips the old roof down back to the clear decking. Some people think there is no problems with applying brand new shingles overtop of the old ones. This is not the best practice and for the best looking and longest lasting roof tearing off the old roof is recommended.
poynor roofing
Watch Video Poynor Roofing video
New To Phoenix or Peoria and need church? peoria churches az
Related Roofing Articles
Poynor Roofing Shingling Phoenix Roofs
Poynor Roofing has been fixing a lot of houses in the Phoenix area for some time now. The type of repair work that tends to be the most common lately is the storm damage incurred from the October storm. Insurance Is paying to replace many roofs in the Phoenix area due to the massive storm that swept through the area last year.
There seems to be all kinds of different types of damage incurred from the massive storm last year in the state of Arizona. There are many types of homes in the Arizona area and a whole diversity of roofs. There are roofs in the area that are damaged and others that are in perfect shape.
One of the key factors to determining if the house may have potential storm damage in the Phoenix area is the storm path. If there was hail that went over an area of the city, it is very possible the house incurred some type of damage. Another important thing for deciding if a home is a candidate for storm damage is the size of the hail that hit the neighborhood.
Its really hard to know what the exact size of the hail was in a given neighborhood buy only looking at historical data of the storm, but it does give a good estimate for approximation of hail size.
Poynor Roofing Looks at Shingles
Another major factor for a home being possibly damaged by the last storm is the type of roof on the house. Some styles of material are incredibly durable such as tile and most likely would have minimal damage.
Poynor Roofing has been finding shingled houses to have the most visible damage in the Phoenix Area. There are several types of shingles used in the valley, but in general 3 tab and architectural shingles are the most common to be damaged.
poynor Roofing
poynor roofing
Watch Video Poynor Roofing
New To Phoenix or Peoria and need church? peoria churches az
Related Roofing Articles
Ptiched Roof and Flat Roofs
The battle between pitched roofs versus flat roofs is an ongoing one especially when you are thinking of which is the best choice for your home or building. The answer for this typically varies depending on the mainly on the local climates and the needs of your building.
In certain countries where there is heavy downpour of rain that can result with high risk of water leakages on the building top, pitched roofs are considered the best choice. From a practical standpoint, it has the higher capacity to evacuate the water away from the building below while a flat roof has the ability to retain water on the top of the building. Stagnant water on top of building with flat roofs will find a way to go down and this can be damaging to your building and the carpets and furniture inside it.
Houses that are built using this type of roof go way back as they are most efficient in water evacuation. The design has been used for some time now that it is considered the best way to have your home or building complement the landscape even with a house that can have a modern look and style.
From a technical perspective, there is a need for water to be directed correctly on a pitched roof to prevent concentration of water in some areas such as spaces that are being obstructed by walls or water that is directed towards the house or building itself. It is important that the architecture of is made with a goal to really remove water and not letting it stagnate onto your home.
[removed][removed]
Related Roofing Articles
Changing Tile Roofs
Many people suffer roof leaks and water damage because of broken or shattered roof tiles. Changing tiles can be very expensive, depending on the roofing contractor you hired and the materials used. Roofing repairs require money which, unfortunately, may not be readily available during these tough economic times. What most do not realize is that as long they can find decent tile pieces and a sturdy ladder, they can do the repair themselves.
A do-it-yourself tile roof repair requires some tools. Obviously, you will need roof tiles for replacement, a disc cutter, nails, hammer, measuring tape, sealants, and a putty knife. Other tools are optional, such as timber wedges, wire cutters, and wire ties. Make sure you have the correct replacement tiles as there are many kinds or it will cost you unnecessary damage and additional expenditures.
Once you have the correct replacement tiles, raise the row of tiles immediately above the one that is to be replaced.
You can use a flat pry bar or chisel for this. Make sure that your tool is pointed in the same direction as the roof tiles so that both of the tiles above the broken one are elevated. Use the hammer handle or a couple of softwood edges to support the tiles while you work.
Be gentle with the tile roof Miami residents are using. If the tile to be replaced is beneath, try reaching in under the tile above with cutters to cut the ties. Otherwise, you will need to enter the roof space to free said tile.
Once you have the broken tile, use a brick trowel to lift the tile up over the baton underneath and slide it down and out.
Afterwards, you can then remove the roof tiles. Most roof tiles are not nailed down. Instead, the tile roof Miami homeowners use have nubs that rest behind small boards that run horizontally under them. You will have to lift up the back end of the tile to slide it out. A steeper sloped roof is more likely to have its tiles nailed down. Be careful when exerting pressure on the tiles when prying.
Slide the new tile roof Miami residents use in the old tile’s place. Remove the pry bars so that the adjacent tiles fall back into place. Press the roof tiles firmly into place by squeezing them gently so that the adhesive spreads out evenly. Let the adhesive dry for 24 hours following the replacement procedure.
If you have questions, please visit us at www.istuetaroofing.com for complete details and answers.
Builders Suggestions: Tiling Roofs
Traditionally tiles were set making use of the 'wet method'. This involved soaking the tiles in water then letting all the excess water dry off. Even though the biscuit of the tile was still damp, mortar in the ratio 1 cement to 1 lime to 2.5 sand was applied to the back of the tile and fixed to the wall. The substrate (wall) was also moistened slightly to help it bond.
Nowadays, tiles are fixed making use of either a thin (3mm) or thick (6mm) bedding of adhesive. Cement based adhesives will need to be left to stand for ten minutes after mixing and then re-agitated before use. The adhesive is spread approximately one square metre at a time and also the tiles laid over. Bicatura tiles have a dry biscuit which is incredibly absorbent and will need to be moistened slightly or laid on a wet adhesive.
Joint widths between tiles really should be consistent and this is ideally achieved with plastic spacer lugs which are inserted at every corner. Spacers vary in width from 1 to 6 mm. Extruded tiles need wider joints although vitrified tiles look finest with narrow joints. Tiles that have dimensional irregularities, which is, they are out of square or vary in size, will require a wider joint to conceal the trouble.
Twenty-four hours later when the adhesive has set, the tiles may be grouted. A fast check of the joins to be sure that no excess adhesive has oozed to the top of the tiles will make certain a neat finish. Excess grout should be wiped clean to leave even and clean joints. Normal rinsing of the sponge will ensure a smooth finish. After the plumber has put within the toilet pans the tiler must return to grout around the base of the pans and to check all his work .
The three rules of tiling are that the tiles must be laid Plumb, Level and Square. This can prove hard when the walls are not plumb, level or square! Increasing the amount of adhesive will not usually solve discrepancies and in cases where the problem is excessive the plasterer will need to come back to rectify his work prior to tiling.
Timber or particleboard floors can be tiled over if a substrate of cement mortar 35mm thick with bird wire reinforcing is laid over a polythene sheet and the tiles are glued down with a highly flexible adhesive. Alternatively, a fibre cement sheet might be employed in place of the mortar substrate then the tiles glued directly to that.
To obtain a balanced and visually pleasing result the tiler must prevent narrow strips of tiles. This is most important in passageways, entry areas and either side of windows. For this reason the tile set-out really should be made only after all of the elements are considered.
To create a good tile set-out, take into account:
The location of floor wastes.
The shape of tiles. Rectangular wall and floor tiles won't enable joint matching between all the walls and floor.
The location of windows and door edges.
If patterned, tiles have to be matched.
Mirror height may well affect the location of border tiles.
In passageways the set-out ought to be from a centre line running down the middle of the passage. This will guarantee even cuts on both sides. In entry areas tiles need to also be laid from the centre out. Since the entry is normally a little are and the tile imbalances will likely be picked at a glance, the tiler really should draw diagonals from every corner of the room to discover the centre point and begin tiling from that point out. Then all edge pieces will be equal in size on opposite walls.
The tiler really should use whichever approach allows for the largest pieces at the perimeter of the room. Alternatively, tiles could be laid at 45" to the walls. This won't only eliminate narrow strips of tiles at the edges but will also conceal the difficulty of out-of-square walls. If a border tile is used then of course this should follow the wall edge.
As a self proclaimed expert builder and renovations expert this author usually works as a deck builder but also builds extensions, patios and garages and sometimes works as a subcontractor on large whole house renovation projects in Brisbane, Queensland, Australia.
Find More Tile Roof Articles
Poynor Roofing Fixing Roofs
There has been a lot of storm damage recently in the Phoenix, Glendale area that Poynor Roofing has been fixing. The recent storm damage was caused by the October Hail storm. This was not only one of Arizonas largest hail storms, it also was one the largest storms on record.
The Storm did have big hail, many places having over 2 in diameter hail. But this size hail in and of itself is not usually worthy of the kind of attention this storm has garnered. There have recently been storms, one in South Dakota that the hail stones were over softball size in diameter and weighing in at over a pound per stone.
The reason why the Phoenix storm was so destructive wasnt only because of the large hail the storm caused, but because of the far reaching tentacles of this storm. There has been damage reported as far west as Peoria Az all the way east to Mesa Arizona.
Poynor Roofing Fixes More
There are still more fresh claims being reported to the insurance company on a daily basis. There is one insurance company reporting nearly 1200 fresh claims a week still 4 months after the storm. One adjustor stated that only 30% of their costumers they thought would call have called in a claim yet.
Poynor Roofing still Getting New Calls
There are still many concerned home owners calling Poynor Roofing and asking if their roof can still be inspected. It is still a good time to get a roof inspection done for this last storm and if there is notable storm damage, the insurance companies will still pay to replace the roof.
It is true that insurance companies will not always pay to replace your roof from storm damage, but right now is still a good time to let them know if you have some damage. Many insurance companies still have their catastrophe teams in town to help the local companies with the claims process. Call Poynor Roofing Today for a free roof inspection.
Watch VideoPoynor roofing Phoenix roof
New To Phoenix or Peoria and need church? peoria churches arizona